!

Metric High Speed 2.0 mm Drill Bit
79188
!
Purchase 6 or more at $0.75 each
Metric High Speed Steel 2.0mm Drill Bit

Metric High Speed 2.35 mm Drill Bit
79189
!
Purchase 6 or more at $0.75 each
Metric High Speed Steel 2.35mm Drill Bit

Metric High Speed 3.0 mm Drill Bit
79190
!
Purchase 6 or more at $0.75 each
Metric High Speed Steel 3.0mm Drill Bit

Steel Drill Bit Set 20 Pieces #61 - 80
79131
!
This 20 piece set of #61 - 80 drill comes in a very convenient dispensing box. Slide the top to the drill you want, tilt, and out it comes. Super for kit building. A nicely made imported set.
Use with pin vise 79000 or 79001

Titanium Coated Drill Bit Set 20 Pieces #61 - 80
79145
!
This 20 piece titanium coated drill set of #61 - 80 drill comes in a very convenient dispensing box. Slide the top to the drill you want, tilt, and out it comes. Super for kit building. A nicely made imported set.
Use with pin vise 79000 or 79001

Diamond Drill Bit Set 20 Pieces #61 - 80
79132
!
This 20 piece set of #61 - 80 DIAMOND TIPPED drill bits comes in a very convenient dispensing box. Slide the top to the drill you want, tilt, and out it comes. Super for plastic kits and precise drilling. A nicely made imported set.
Use with pin vise 79000 or 79001

Diamond Coated Drill Bits 10 Pieces
79147
!

Diamond coated drill bits 10 pieces are on 1/8" Shanks and range in sizes #42 - #70. These are perfect for drilling glass, ceramics, and metal. Comes with a convenient storage case and dispenser.

Porter Cable Black Sheild Split Point 7 Piece Drill Bit Set
79140
!
This 7 piece set includes 1/16”, 5/64”, 3/32”, 7/64”, 1/8”, 5/32” and 3/16”. It has a black shield finish and resists corrosion. They are precision ground for accurate hole size and comes with an index box.

Drill Gauge 61 - 80
79133
!

This American made drill gauge is a must for 61 to 80 drills.  When you spill your drills, pop it into the holes for a perfect size every time.

Rule With Drill Bit Gauge 6 inch
10366
!
Purchase 2 or more at $2.50 each

A super handy 6 inch stainless steel rule with inches and mm, including a drill bit gauge with the following sizes 1/16, 5/64 3/32, 1/8, 9/64 5/32, 11/64 3/16, 13/64, 7/32 & 1/4.

#1 thru #60 Drill Bit Set
79135
!

This nice inexpensive set is perfect for the modeler.  Comes in an indexed box.  Less than 50 cents per drill bit.  These are High Speed Steel bits.

Titanium Coated Drill Bits #1 thru #60
79136
!
This 60 piece #1 - 60 Titanium Nitride coated drill set will last 6 times longer then regular drill bits. Bits # 1 - 29 are milled and bits # 30 - 60 are ground. All bits have 118º points. The metal index box is numbered with the drill bit size stamped on each row.

Screw Ease Out #1

79195
!
Made in USA

This #1 ezy-out is 5/64 and used to remove small screws that have broken or have stripped heads. Use with drill or hand tap.

Metric Tap & Die Set
79200
!
A 30 piece super little kit, comes with the following sizes,1.0, 1.1, 1.2, 1.4, 1.6, 1.8, 2.0, 2.2 & 2.5, with 2 taps for each die.  The handle will do both taps and dies.

SAE Tap & Die Set
79205
!
A 30 piece super little kit, comes with the following sizes, 0-90, 0-80, 1-64, 1-72, 2-56, 3-48, 3-56 & 4-40, with 2 taps for each die. The handle will do both taps and dies

Mini Router Bit 10 Piece Set
95759
!
These bits are perfect with any Dremel©. If you're into fine detail work, then this set fits the bill. The bits have a 1/8" shank and should be used with a full router base or router table. The set includes a 3/16" cove, 1/8" corner round, 1/4" straight, 3/16" straight, 1/8" straight, 3/32" beading, 1/8" rabbeting, 1/4" plunge ogee, 1/4" core box, and a 1/4" v-groove. Made from high speed steel and includes a wooden box for storage.

Keyless Finger Chuck
95420
!
This is a Keyless Finger Chuck that goes from 0 to 1/8 inch. It only fits the following Dremesl® #275, 285, 410, 595, 851, 950 and the new Ryobi.

Finger Chuck with Collets
95450
!
This is a Finger Chuck with a 3/32 shaft. I will give you a free 3/32 collet just in case you don't have one. It goes from 0 to 3/32. For best results, I advise you to cut the shaft a little and always start at the lowest speed. I have sold hundreds of these with great results.

Mini Finger Chuck
95460
!
This is a Mini Finger Chuck with a 1/8 inch shaft. This is designed to hold those 70 to 80 drill bits in your Dremel® or moto tool. Only use with multi speed tools on slow.

Finger Chuck for Power Screwdrivers Regular
95465
!
This is a Finger Chuck that is perfect for your 1/4 inch power screw driver. It is great for holding bits from 0 to 1/8 inch.

Finger Chuck for Power Screwdrivers Large
95466
!
This is a Finger Chuck that is perfect for your 1/4 inch power screw driver. It is great for holding bits from 0 to 1/8 inch.

# 50 High Speed Steel ( HSS ) Drill Bit
79150
!
Purchase 6 or more at $0.75 each
These are wire gauge # 50 high speed steel drill bits, perfect for all types of hobbies, crafts, jewelry making and fine work.

Size Chart
Wire Gauge # 50
Decimal (inches) 0.0700
Metric (millimeters) 1.7780

Click here to download a Wire Gauge Drill Bit Chart or Metric Drill Bit Chart

# 51 High Speed Steel ( HSS ) Drill Bit
79151
!
Purchase 6 or more at $0.75 each
These are wire gauge # 51 high speed steel drill bits, perfect for all types of hobbies, crafts, jewelry making and fine work.

Size Chart
Wire Gauge # 51
Decimal (inches) 0.0670
Metric (millimeters) 1.7018

Click here to download a Wire Gauge Drill Bit Chart or Metric Drill Bit Chart

# 52 High Speed Steel ( HSS ) Drill Bit
79152
!
Purchase 6 or more at $0.75 each
These are wire gauge # 52 high speed steel drill bits, perfect for all types of hobbies, crafts, jewelry making and fine work.

Size Chart
Wire Gauge # 52
Decimal (inches) 0.0635
Metric (millimeters) 1.6129

Click here to download a Wire Gauge Drill Bit Chart or Metric Drill Bit Chart